Download the 2.09 version.

2024/11/13 Version 2.09 Changelog

Firmware Update Notice

Increase Two kinds of circularity: ( Square one and Round one)

1. For left joystick: Press the “screen shot ”button + “L3 ”(press left joystick vertically) for 2 seconds, when logo led blinking red, means goes to round one.
2. For right joystick: Press the “screen shot ”button + “R3 ”(press right joystick vertically) for 2 seconds, when logo led blinking red, means goes to round mode.
   And cut off the controller, to maintain.
3. Vice versa. Operate again, when the logo led blinking green, means goes to square mode.

Download the 2.08 version.

2024/10/09 Version 2.08 Changelog

Firmware Update Notice

Fixes a bug affecting the reporting rate of controllers with TMR joysticks.

Toggle Joystick Deadzone

• To switch, press and hold the T button + Plus button + Minus button for 3 seconds while the device is on.

Download the 2.05 version.

2024/05/01 Version 2.05 Changelog

Low Battery Alert

• To enhance your experience and avoid unexpected interruptions, we've added a new feature. Now, when your controller's battery level drops below 15%, the Home button will continuously flash as a reminder to recharge.

Download the 1.26 version.

2024/03/25 Version 1.26 Changelog

Joystick Enhancements:

• Joystick sensitivity fine-tuned.
• Controller Standby Mode:
  A new standby mode was introduced; after 1 minute inactivity, only the Home button remains lit. Pick up the controller to wake it.

RGB Lighting Improvements:

Mode Switch:

• Press the "T button" + “Screenshot button” to toggle between modes.
• In default and rhythm mode, shaking the controller while holding the "T button" activates "Light Shake" mode.
  
  Default Mode:
  The light bar won't highlight with the LT button press.
  The light bar turns off at the dimmest third level, but the ABXY lights remain.
  "Light Shake" function generates random color combinations.
  
  Racing Mode:
  Light-bar is off by default, highlights when LT is pressed.
  RT button press simulates a throttle effect on Light-bar.
  ABXY and Home button colors customizable, tail light is not.
  
  FPS Mode:
  Light-bar off by default, highlights with LT/RT press, enters "Fire Mode" with a long RT press.
  Light-bar matches ABXY button colors when pressed.
  Tail light color is fixed.
  
  Rhythm Game Mode:
  Light-bar highlights with button presses.
  Joystick rotation changes Light-bar color.
  Only Home + ABXY lights are customizable.
  Tail lights match ABXY button colors when pressed (default to red).
  "Light Shake" function for random color combinations.
  
  Breathing Light Mode:
  Lights cycle through colors with each breath.
  Breathing rate is customizable.
  Fixed light colors.
  
  Flowing Rainbow Mode:
  ABXY, Home button, and Light-bar continuously cycle through colors.
  Speed of color transitions is customizable.
  Fixed light colors.

Download the 1.07 version.

1. Download first one and open .

2. plug in 2.4G Dongle.

3. Click button on PC about update and shows success.

4. Pull out 2.4G Dongle.

5. Download second one.

6. Plug in 2.4G Dongle.

7. Open second on software. and you can see a green sucess there.

Note: How to test 2.4G Dongle:

1. Turn controller mode to S not X. ( The button at at the right side of charging port)

2. Pairing with 2.4G dongle with S mode.

3. Make sure the 2.4G Dongle is at XINPUT mode. (then 1000hz polling rate could be test )

Download the latest version V2.15

Write content to answer to common questions your customers may have about your products, shipping policies..

Download the latest version.

Firmware upgrade V3.03 (2023/09/11)

• Optimized Power Management: Improved power consumption. The controller activates from standby only when the Home button is pressed, reducing unnecessary energy use.

• Enhanced Joystick Precision in PC Mode: Upgraded joystick accuracy for a smoother and more precise gaming experience in PC mode.

Firmware upgrade procedure

• Ensure the controller is powered off.
• Press and hold the L3 button (press down on the left stick).
• While holding L3, connect the controller to your PC using the data cable.
• Open the upgrade software and click Update.
• Wait patiently for the firmware upgrade to complete. The entire process takes around 5-10 minutes.
• The controller will vibrate once the upgrade is successful.
• You should perform this firmware upgrade to get the latest features and bug fixes.

Important Reminder:
If an error occurs during the update process, press and hold the Bluetooth pairing button on the controller for 10 seconds to reset it. After resetting, please follow the steps mentioned above to update the firmware.

1. Open the downloaded firmware file.
2. Press and hold the left joystick L3 button with the controller turned off.
3. Connect the controller using the included Type-C data cable (or any data transfer-capable cable).
4. The firmware update button will become highlighted.
5. Click on the update button to begin the update.
Once the update is complete, the controller is ready to use.

You can contact us through our contact page! We will be happy to assist you.